China Professional High Air Pressure DTH Hammer Drill Bit in Drilling Blast Hole with Good quality

Product Description

Blast Hole Mission Drop Center Face DTH Hammer Bits Rock Drill Bit 

Product Description

KINGDRILLING hammer bits are used with Down-the-hole hammers for drilling holes through a wide range of rocks types. In conjunction with DTH hammers, drill hammer bits are designed with a spline drive for rotating the bit in the ground. Drill bits are available in different sizes and different styles so they can drill a wide range of hole sizes.

Rock drill bits Shank type:M3,M4,M5,M6,M8,M1,M12

DTH hammer bits hole diameter: 3”, 4”, 5”, 6”, 8”(85mm-350mm).

 

Product features: 
DTH Drill Bits are produced from premium quality nickel-alloy steel for increased durability and wear characteristics. Specific heat treatment standards and special “stress relief” processes ensure consistent performance. 

Technical Date 

3 Inch Hight Air Pressure DTH bits

Model

Bit Dia.(mm)

NO. X    Button Dia.

NO.Air    Holes(PCS)

Weight(KG)

Gauge

Front

MDHM3-85

85

6*Φ13

4*Φ12

2

4.5

MDHM3-90

90

6*Φ14

4*Φ12

2

4.7

MDHM3-95

95

6*Φ14

4*Φ13

2

4.9

MDHM3-100

100

6*Φ14

5*Φ12

2

5.0

MDHM3-105

105

6*Φ14

5*Φ13

2

5.5

4 inch high air  pressure DTH bits

MDHM4-105

105

6*Φ14

5*Φ13

2

6.0

MDHM4-110

110

7*Φ14

6*Φ13

2

6.2

MDHM4-115

115

7*Φ14

6*Φ13

2

6.6

MDHM4-120

120

8*Φ14

7*Φ13

2

7.0

MDHM4-127

127

8*Φ14

7*Φ13

2

7.4

5 inch high air pressure DTH bits

MDHM5-135

135

7*Φ18

6*Φ14

2

12.5

MDHM5-140

140

7*Φ18

7*Φ14

2

13.5

MDHM5-146

146

7*Φ18

7*Φ14

2

14.0

MDHM5-152

152

8*Φ18

8*Φ14

2

14.4

MDHM5-165

165

8*Φ18

8*Φ16

2

15.0

6 inch high air pressure DTH bits

MDHM6-152

152

8*Φ18

7*Φ16

2

22.0

MDHM6-165

165

8*Φ18

8*Φ16

2

23.0

MDHM6-171

171

8*Φ18

8*Φ16

2

24.0

MDHM6-190

190

9*Φ18

9*Φ16

3

25.0

MDHM6-203

203

9*Φ18

11*Φ16

3

28.0

8 inch high air pressure DTH bits

MDHM8-305

305

12*Φ18

29*Φ16

4

95.0

MDHM8-203

203

10*Φ18

10*Φ16

2

35.0

MDHM8-216

216

10*Φ18

12*Φ16

2

40.0

MDHM8-241

241

12*Φ18

18*Φ16

2

54.0

MDHM8-254

254

12*Φ18

21*Φ16

3

57.0

MDHM8-305

305

12*Φ18

29*Φ16

4

77.0

10 inch high air pressure DTH bits

MDHM10-254

254

12*Φ18

20*Φ16

3

90.0

MDHM10-305

305

12*Φ18

36*Φ16

4

102.0

MDHM10-311

311

12*Φ18

36*Φ16

4

104.0

MDHM10-318

318

12*Φ18

38*Φ16

4

106.0

MDHM10-330

330

14*Φ18

42*Φ16

4

112.0

12 inch high air pressure DTH bits

MDHM12-305

305

12*Φ18

36*Φ16

4

152.0

MDHM12-311

311

12*Φ18

36*Φ16

4

158.0

MDHM12-330

330

16*Φ18

42*Φ16

4

165.0

MDHM12-356

356

16*Φ19

48*Φ16

4

178.0

MDHM12-381

381

16*Φ19

48*Φ18

4

195.0

MDHM125-305

305

12*Φ18

36*Φ16

4

170.0

MDHM125-311

311

12*Φ18

36*Φ16

4

173.0

MDHM125-330

330

16*Φ18

42*Φ16

4

182.0

MDHM125-356

356

16*Φ19

48*Φ16

4

191.0

MDHM125-381

381

16*Φ19

48*Φ18

4

200.0

Kindly Note: We can also design and manufacture the different diameter, holes number, carbide button shape and face shape according to the customers’ requirement.

Our Advantages as below:

1. High quality steels materials. Steel is from CZPT and Tungsten carbide are YK05, or T6 from Element Six in Germany

2. Kingdrilling DTH tools are forged by advanced electron-hydraulic forging hammer.

3.Advanced heat-treatment equipment: multipurpose CZPT heat treatment.

4. Completed moulding (tooling ) departments with many molds available.

5.Professional R&D team,completed quality system.

6.Strict Quality-Check Systems.

 

How to order:

Shank Type + Head Diameter + Face Design + Button Shape

 

FAQ:

1. How to order the products?

A: Please send the inquiry with detail item description or with Model number.

 

2. Can I expect a quality products?

A: Yes. mature production technology ensuring the quality satisfy international request.

 

3. How to control quality?

A: We have our own experienced QC team,there will be strict inspection and testing for each order before shipping out.

 

4. Competitive price:

A: KINGDRILLING factory can supply you the lowest price due to direct sale to customers without distributor.

 

5. What is the Application?

Mining, Quarrying, Tunneling, Construction, Geological Exploration, Water-well Drilling, Oilfield & Gas Industries.

 

6. Product feature

Kingdrilling DTH tools are forged by advanced electron-hydraulic forging hammer, and harness process is managed by multipurpose CZPT heat treatment.

 

7. How to choose the suitable head face of the DTH drill bit?

a. Concave:

Suitable for all kinds of formation, especially for deep well drilling, perpendicularity of the hole is wonderful.

b. Convex: 

Suitable for the formation of moderate hardness stratum, drilling efficiency is good, borehole perpendicularity is moderate.

c. Flat:

Suitable for special hard formation stratum, especially for fracture, crack spacing and complex formation drilling effect is very good, has the good perpendicularity of the borehole.

Product Application:

About our Company 
Kingdrilling Machinery Co. , Ltd is established in 2005 years. Located in HangZhou East Lake High-tech Development Zone, is 1 of the most important manufacturers specialized in researching and producing Casing drilling system, DTH hammer, DTH bit, thread DTH bits, taper DTH bits, coupling sleeve, Anchor, Shank adapter, coal picks and so on.

Relying on the university resources and talent advantages in Optical Valley region, combining with multiple laboratories in universities, we focused on developing the newest products system.

Transport:

Package and Delivery:
Packed by Carton or Wooden cases.

Delivery:

  1. Goods in stock can be delivered within 5 days.
  2. DTH Bits production time is about 15 days.
  3. DTH Hammer product time is about 30 days.

More products:

 

The Different Types of Splines in a Splined Shaft

A splined shaft is a machine component with internal and external splines. The splines are formed in 4 different ways: Involute, Parallel, Serrated, and Ball. You can learn more about each type of spline in this article. When choosing a splined shaft, be sure to choose the right 1 for your application. Read on to learn about the different types of splines and how they affect the shaft’s performance.
splineshaft

Involute splines

Involute splines in a splined shaft are used to secure and extend mechanical assemblies. They are smooth, inwardly curving grooves that resist separation during operation. A shaft with involute splines is often longer than the shaft itself. This feature allows for more axial movement. This is beneficial for many applications, especially in a gearbox.
The involute spline is a shaped spline, similar to a parallel spline. It is angled and consists of teeth that create a spiral pattern that enables linear and rotatory motion. It is distinguished from other splines by the serrations on its flanks. It also has a flat top. It is a good option for couplers and other applications where angular movement is necessary.
Involute splines are also called involute teeth because of their shape. They are flat on the top and curved on the sides. These teeth can be either internal or external. As a result, involute splines provide greater surface contact, which helps reduce stress and fatigue. Regardless of the shape, involute splines are generally easy to machine and fit.
Involute splines are a type of splines that are used in splined shafts. These splines have different names, depending on their diameters. An example set of designations is for a 32-tooth male spline, a 2,500-tooth module, and a 30 degree pressure angle. An example of a female spline, a fillet root spline, is used to describe the diameter of the splined shaft.
The effective tooth thickness of splines is dependent on the number of keyways and the type of spline. Involute splines in splined shafts should be designed to engage 25 to 50 percent of the spline teeth during the coupling. Involute splines should be able to withstand the load without cracking.

Parallel splines

Parallel splines are formed on a splined shaft by putting 1 or more teeth into another. The male spline is positioned at the center of the female spline. The teeth of the male spline are also parallel to the shaft axis, but a common misalignment causes the splines to roll and tilt. This is common in many industrial applications, and there are a number of ways to improve the performance of splines.
Typically, parallel splines are used to reduce friction in a rotating part. The splines on a splined shaft are narrower on the end face than the interior, which makes them more prone to wear. This type of spline is used in a variety of industries, such as machinery, and it also allows for greater efficiency when transmitting torque.
Involute splines on a splined shaft are the most common. They have equally spaced teeth, and are therefore less likely to crack due to fatigue. They also tend to be easy to cut and fit. However, they are not the best type of spline. It is important to understand the difference between parallel and involute splines before deciding on which spline to use.
The difference between splined and involute splines is the size of the grooves. Involute splines are generally larger than parallel splines. These types of splines provide more torque to the gear teeth and reduce stress during operation. They are also more durable and have a longer life span. And because they are used on farm machinery, they are essential in this type of application.
splineshaft

Serrated splines

A Serrated Splined Shaft has several advantages. This type of shaft is highly adjustable. Its large number of teeth allows large torques, and its shorter tooth width allows for greater adjustment. These features make this type of shaft an ideal choice for applications where accuracy is critical. Listed below are some of the benefits of this type of shaft. These benefits are just a few of the advantages. Learn more about this type of shaft.
The process of hobbing is inexpensive and highly accurate. It is useful for external spline shafts, but is not suitable for internal splines. This type of process forms synchronized shapes on the shaft, reducing the manufacturing cycle and stabilizing the relative phase between spline and thread. It uses a grinding wheel to shape the shaft. CZPT Manufacturing has a large inventory of Serrated Splined Shafts.
The teeth of a Serrated Splined Shaft are designed to engage with the hub over the entire circumference of the shaft. The teeth of the shaft are spaced uniformly around the spline, creating a multiple-tooth point of contact over the entire length of the shaft. The results of these analyses are usually satisfactory. But there are some limitations. To begin with, the splines of the Serrated Splined Shaft should be chosen carefully. If the application requires large-scale analysis, it may be necessary to modify the design.
The splines of the Serrated Splined Shaft are also used for other purposes. They can be used to transmit torque to another device. They also act as an anti-rotational device and function as a linear guide. Both the design and the type of splines determine the function of the Splined Shaft. In the automobile industry, they are used in vehicles, aerospace, earth-moving machinery, and many other industries.

Ball splines

The invention relates to a ball-spinned shaft. The shaft comprises a plurality of balls that are arranged in a series and are operatively coupled to a load path section. The balls are capable of rolling endlessly along the path. This invention also relates to a ball bearing. Here, a ball bearing is 1 of the many types of gears. The following discussion describes the features of a ball bearing.
A ball-splined shaft assembly comprises a shaft with at least 1 ball-spline groove and a plurality of circumferential step grooves. The shaft is held in a first holding means that extends longitudinally and is rotatably held by a second holding means. Both the shaft and the first holding means are driven relative to 1 another by a first driving means. It is possible to manufacture a ball-splined shaft in a variety of ways.
A ball-splined shaft features a nut with recirculating balls. The ball-splined nut rides in these grooves to provide linear motion while preventing rotation. A splined shaft with a nut that has recirculating balls can also provide rotary motion. A ball splined shaft also has higher load capacities than a ball bushing. For these reasons, ball splines are an excellent choice for many applications.
In this invention, a pair of ball-spinned shafts are housed in a box under a carrier device 40. Each of the 2 shafts extends along a longitudinal line of arm 50. One end of each shaft is supported rotatably by a slide block 56. The slide block also has a support arm 58 that supports the center arm 50 in a cantilever fashion.
splineshaft

Sector no-go gage

A no-go gauge is a tool that checks the splined shaft for oversize. It is an effective way to determine the oversize condition of a splined shaft without removing the shaft. It measures external splines and serrations. The no-go gage is available in sizes ranging from 19mm to 130mm with a 25mm profile length.
The sector no-go gage has 2 groups of diametrally opposed teeth. The space between them is manufactured to a maximum space width and the tooth thickness must be within a predetermined tolerance. This gage would be out of tolerance if the splines were measured with a pin. The dimensions of this splined shaft can be found in the respective ANSI or DIN standards.
The go-no-go gage is useful for final inspection of thread pitch diameter. It is also useful for splined shafts and threaded nuts. The thread of a screw must match the contour of the go-no-go gage head to avoid a no-go condition. There is no substitute for a quality machine. It is an essential tool for any splined shaft and fastener manufacturer.
The NO-GO gage can detect changes in tooth thickness. It can be calibrated under ISO17025 standards and has many advantages over a non-go gage. It also gives a visual reference of the thickness of a splined shaft. When the teeth match, the shaft is considered ready for installation. It is a critical process. In some cases, it is impossible to determine the precise length of the shaft spline.
The 45-degree pressure angle is most commonly used for axles and torque-delivering members. This pressure angle is the most economical in terms of tool life, but the splines will not roll neatly like a 30 degree angle. The 45-degree spline is more likely to fall off larger than the other two. Oftentimes, it will also have a crowned look. The 37.5 degree pressure angle is a compromise between the other 2 pressure angles. It is often used when the splined shaft material is harder than usual.

China Professional High Air Pressure DTH Hammer Drill Bit in Drilling Blast Hole     with Good qualityChina Professional High Air Pressure DTH Hammer Drill Bit in Drilling Blast Hole     with Good quality